1/2 inch is fine for delts but you may need to use 27g or heat the oil up before pinning depending on how thick of a carrier oil you are using. Something like gso, for example may be too thick to push through.Could a 29g 1/2 inch insulin pin be used for IM injections in the delt? Or is 1/2 an inch too short
MCT oil. Should I heat it up still?1/2 inch is fine for delts but you may need to use 27g or heat the oil up before pinning depending on how thick of a carrier oil you are using. Something like gso, for example may be too thick to push through.
I’ve personally never used anything higher than 27g for oils. It’s completely up to you if it pushes through. If won’t hurt if you do but if it doesn’t push through then yeah you’ll have to heat it up.MCT oil. Should I heat it up still?
I’ve personally never used anything higher than 27g for oils. It’s completely up to you if it pushes through. If won’t hurt if you do but if it doesn’t push through then yeah you’ll have to heat it up.
Yes 1/2 inch 27g is what I use for delts. And I bet, an inch is long for delts lolFound 27g 1/2 inch online. I’ll get those. So 1/2 inch is long enough for delts? Last time I used an inch it was a terrible experience
27G x 1/2 is fine, but it will take forever to push a ml. Also, the insulin syringes are kind of delicate and the throw is quite long (thin barrel) so it’s difficult to keep such a short thin needle buried while you push thick oil through.Found 27g 1/2 inch online. I’ll get those. So 1/2 inch is long enough for delts? Last time I used an inch it was a terrible experience
I use 18 gauge to draw. I’m just asking if 27 gauge 1/2 inch would be good for injecting delts27G x 1/2 is fine, but it will take forever to push a ml. Also, the insulin syringes are kind of delicate and the throw is quite long (thin barrel) so it’s difficult to keep such a short thin needle buried while you push thick oil through.
A better bet would be to buy a standard 2ml or 3 ml syringe with an 18G drawing needle attached and a separate box of 27 x 5/8 or 27 x 1/2 needles….. I like the 5/8 better as I can use them glutes delt or even lats.
27 x 1/2 is fine, you didn’t mention that in your 1st post. You asked about using a slin pin.I
I use 18 gauge to draw. I’m just asking if 27 gauge 1/2 inch would be good for injecting delts
Except for GH, I use 25g x 5/8” needles for all compounds. Delts? No issues. Can’t even feel it. Some people go 1” needles, which is insane to me.Could a 29g 1/2 inch insulin pin be used for IM injections in the delt? Or is 1/2 an inch too short
Yeah… I tried 1 inch in the delt and never again man hahahaExcept for GH, I use 25g x 5/8” needles for all compounds. Delts? No issues. Can’t even feel it. Some people go 1” needles, which is insane to me.
I bought a whole box on Amazon they work!Found 27g 1/2 inch online. I’ll get those. So 1/2 inch is long enough for delts? Last time I used an inch it was a terrible experience
If you pin daily what sites are you rotating? How much are you pinning? What do you use to heat up Oil?I use 29 gauge 1/2 in inch to pin. Works for GSO and MCT, I just warm the bottle up a little before I draw it up. Works fine just be patient and draw/push slowly.
I also pin daily so the volume is never much (around half cc during a blast and much less while cruising.)