powder doesnt dissolve?

[Booker]

total noob to homebrewing so excuse the dumb question.

20% BB, 1% BA, MCT oil. 60mg/ml superdrol. Nothing special. I stirred and heated my solution for around 30 minutes and there are many powder “rocks” refusing to dissolve.
Question: Can i assume my raws are dirty as hell OR is that normal and i can just draw that stuff, push it through a 0.22 um syringe filter and be good? I mean even if i assume the powders purity sucks, a good PVDF syringe filter should make that awful purity, void, no?

EDIT: Slightly increase the BB by a couple percent and that was enough to dissolve 60mg/ml.
EDIT: Needed 30% BB for 100mg/ml, seems to crystialize in tiny amounts.
EDIT: 100mg/ml, 0.2ml injection stinged a little bit. No PIP, injected into my glute with a 8mm needle.

 

[Forthewin1123]

@Booker what temp are you reaching? You should not need.to go over.20% bb… I’ve brewed superdrol handful of times… but it does need some heat. I would say atleast 160-180° f… I would try that before adding anymore bb…

 

[Forthewin1123]

Filtering it before its fully dissolved will give you 10mg/ml or less or more… and it will possibly clog filter and end up with zero superdrol…

 

[Booker]

@Forthewin1123 Im brewing at 100mg/ml. I did 60mg/ml with 20% BB just fine even though it still took a long ass time. But really want the higher concentration. Im stirring like a mf under heat for like 30 minutes and more.
Feel like i need to go like 30-40% with the BB before it dissolves at that concentration… Im at about 150° F.

 

[Forthewin1123]

@Booker ok that changes everything… 100mg/ml I’ve never seen before… I know once bb is 30% and higher she starts to bite… and bites hard as you go up. I think we habe never seen it higher then 40-60mg/ml for a reason… you may not get that recipe to work…

 

[Booker]

@Forthewin1123 Managed to dissolve the sdrol in 30% BB. Gonna inject 0.2ml and see how it feels.
Edit 1: When you said it bites, i thought you were simply talking about PIP. But that stuff actually stings. Will report back with the PIP tomorrow. I think im seeing tiny, tiny crystal looking floaters in my vial so i assume the sdrol is crashing, falling out of suspension? Will try 80mg/ml tomorrow and hope it’ll be perfect then. 0.25ml injections for 20mg sdrol per day is fine

 

[Forthewin1123]

@Booker I did mean pip… but it is a initial bite followed by soreness… goes away in an hour or 2 usually tops… and that’s the high % of bb that causes that from what I’ve learned and been told. Of.ypu have alot of issues… I would restart… and brew it at 45mg/ml… for a 40mg/ml finished product… if you do that it’s 2%/20% and completely pain.less… and I habe never needed more.then.40mg a day… 30mg is my.sweet spot… of I go higher I end.up having.to stop the cyxle.in 2 to 3 weeks because.its makes.me.feel like dog shit because it’s so toxic…that’s just my experience though

 

[Booker]

@Forthewin1123 What? I have issues?
Why would i go down to 40mg/ml when i brewed 60mg/ml in 22% BB just fine. My 100mg/ml seems fine too. The injection stinged for a couple minutes and i have no PIP. Ill probably stay at 80mg/ml.
If i have to inject like 1cc everyday ill never go through with the cycle. I hate daily injections so i need these low injection amounts. 100mg/ml allows me to do that.

 

[Forthewin1123]

I said "if "you have alot of issues… I inject .6-.7 ml of superdrol everyday in one of my delts when running it… it’s annoying but…this shit isn’t always easy. I may try to brew some with a higher concentration… less oil injection

 

[Booker]

@Forthewin1123 It says “Of.ypu” for me, prolly just a typo.
Anyways 80mg/ml seems to hold just fine. No crashing, no PIP, doesnt sting at 30% BB. FYI.