Semi-Finished Producta

[Hypotenuse90]

I’m looking for semi-finished injectables to finish at home. It is my understanding that I only need to filter them before use and that even that is not necessary and that they are safe to inject the way they are.

Where can I get semi-finished injectables?

Where do I get the equipment to filter the semi-finished injectables?

How do I filter the semi-finished injectables?

Can I inject the semi-finished injectables the way that they are? Why or why not?

Where can I get Mast E for cheap? The whole reason I’m doing this is to get Mast E for cheap.

Thank you,

H

 

[BulKKing_Labs]

Hi @Hypotenuse90 I am an unverified source on here, since the migration I’m not sure if I’ve been stickied/pinned as such; however, I offer larger vials of already filtered brew. Right now, I have about 40 50mL Test E 250 for $100 (Out of Stock on the 100mL) Tren A 100mg 50mL vials for $120 (equivalent to $24 a vial). If you’re in a clean enough room, you can decrimp (you can find one on Amazon for 20mm vial necks) the vial, keep the stopper on, and quickly pour the liquid into the new vial (which should be sterilized by washing and heating in the oven for 40 minutes on 400). As soon as you’re ready to fill, just pop the rubber stopper off and pour to the point at which 10mL is. Some 10mL don’t fill way to the top (some advertise as 10mL but can take 14mL). You can find some supplies on med lab supply. Vials, silicone stoppers, flip top caps. I have all of those things as well which we could make a deal for since I haven’t priced equipment. I know you said that you want to know where you can get mast e for cheap, and that’s your main point; I will eventually brew mast e in 50mL vials and perhaps a 100mL vial if it is requested and in right timing (I’m about to receive some in the next week or so, so this is the right timing). Pricing wise, I would have to calculate what I would charge for a 50mL and a 100mL. It would be 200mg/mL. Probably $150 for a 50mL (equivalent to $30 a vial at 10mL) and $250 for a 100mL vial (equivalent to $25 per 10mL vial.

I don’t necessarily condone the method of just “pouring” into a sterilized vial so much as having a small media bottle with a bottle top dispenser to dispense 10mL almost exactly to 10mL. Or, even better, get some 10mL syringes and and draw out 10mL, get some 0.22um micron filters (also on Amazon) to replace the needle at the tip, and dispense the liquid that way. You’d have double filtered product.

I hope I can help, and this would be all without having to filter any of the products. I’ll do all of that for you.

 

[CerealHobbiest]

I think it was Dragon Ordinance that had the semi finished.

You can filter one of two ways
You need a .22 micron whatcom syringe filter. Put a air release needle in the top of the bottle. You can use a caulking gun and a 60 ml syringe (get a luer lock tip) and filter that way.

Second using a bottle top media filter and you need a vacuum source. The filters run 80 bucks.

If your only doing your gear then do the syringe filter. If your trying to source for a few people the bottle top filter seems a lot better.

 

[RarelyThere2]

Purple panda carries this. It’s crazy cheap but I’ve read it comes in jars with twist tops. I just question how sterile that is. I’m tempted to give it a go.

 

[MattyG128VA]

@BulKKing-Labs What do you currently have in stock?