Soco test ace crystals

[Deadlift_heavy]

So I just noticed I have some crystals in my test ace, any advice on how to break these down? I’m warming it in a pan with water there’s a lot less than there was when I first saw them but there’s still a few in there

 

[MentalPariah]

Candle warmer works especially well

 

[mdwilson2011]

+1 candle warmer for 10-15 minutes. Recently used some old Enhanced Pharma test ace that was completely crashed. 15 minutes on the warmer and it was fine. Pinned smooth too.

 

[system]

3 votes candle warmer, and that’s what was suggested to me by SoCo himself.

 

[Dexter]

I have some of that same SoCo Test Ace.

I always use a coffee cup warmer, once it’s suspended mine has held without crashing again for several weeks. Coffee warmer and Candle warmer are basically the same thing, you can pick them up for $10-12. Set it on the table and check it every 5 minutes so you don’t cook if for too long.

Also make sure you inject this IM, you subQ this stuff and you’re gonna have some PIP even though it’s only 100mg/ml.

 

[system]

^^ even cheaper if you have a michaels near by, a mere $5! https://www.michaels.com/ashland-basic-elements-candle-warmer/10313465.html

 

[Jalisco07]

I got the same thing with @“SouthernCompounding” test ace. Heated it up and became crystal clear. After if was some of the best test ace I’ve used. Top of the line.

 

[Deadlift_heavy]

Dexter" pid='69619' dateline='1569380703:

I have some of that same SoCo Test Ace.

I always use a coffee cup warmer, once it’s suspended mine has held without crashing again for several weeks. Coffee warmer and Candle warmer are basically the same thing, you can pick them up for $10-12. Set it on the table and check it every 5 minutes so you don’t cook if for too long.

Also make sure you inject this IM, you subQ this stuff and you’re gonna have some PIP even though it’s only 100mg/ml.

I’ve been pinning Ed 50mg cuz I’m also running some test Enanthate. Was thinking about doing Subq, so it’s not a good a idea?

---

Thanks for the replies I heated it in the pot with water for a good 25 mins and all the crystals dissolved.

 

[Harbenger]

Should OP vent the vial when warming? Slin pin or something larger?

 

[system]

Harbenger" pid='69634' dateline='1569406167:

Should OP vent the vial when warming? Slin pin or something larger?

I’ve never done so with a candle warmer but with the stove or oven I cannot comment

 

[Dexter]

Deangelobrooks" pid='69629' dateline='1569388389:

I’ve been pinning Ed 50mg cuz I’m also running some test Enanthate. Was thinking about doing Subq, so it’s not a good a idea?

You can try pinning SubQ, but I wouldn’t pin more then 0.2ml in one spot at a time. Just try out a very small amount and see how it goes. If you pin 0.5ml of Test Ace in one SubQ spot I think you’re not gonna enjoy it and that’s nothing against SoCo’s Test-A, it’s just the nature of acetate esters and the volume at which you are wanting to inject.

Like anything, start small and build up.

 

[Deadlift_heavy]

Dexter" pid='69641' dateline='1569419017:

Deangelobrooks" pid='69629' dateline='1569388389:

I’ve been pinning Ed 50mg cuz I’m also running some test Enanthate. Was thinking about doing Subq, so it’s not a good a idea?

You can try pinning SubQ, but I wouldn’t pin more then 0.2ml in one spot at a time. Just try out a very small amount and see how it goes. If you pin 0.5ml of Test Ace in one SubQ spot I think you’re not gonna enjoy it and that’s nothing against SoCo’s Test-A, it’s just the nature of acetate esters and the volume at which you are wanting to inject.

Like anything, start small and build up.

How often are you pinning? I’ve never tried acetate but for the price I figured what the hell. I both sides ventro and got a decent amount of pip, nothing compared to when I started the cycle pinned my quad and thought it was gonna rip when I was doing legs

 

[Dexter]

Right now I’m pinning every 72hrs for everything I do, using multiple injections.

I’ve found even with IM that only injecting .25ml in each spot produces no PIP, so I just draw everything up into one syringe…Test C,A,Mast P and then use 3 needles to inject, one needle for each spot, I also waste less by drawing it up in one syringe as there is about 0.1cc left in syringe.

As for pain subQ, if you use small amounts I think you’ll be fine with Test Ace, don’t dump 0.5ml SubQ into one spot, it will produce a large welt that will often times travel through the fat creating an irritating lump.